Salam Academy
Electricity · Subtopic 3 of 5

Series and Parallel Circuits

In series, the current is the same everywhere, p.d.s add up to the supply, and resistances add. In parallel, each branch gets the full p.d., the branch currents add up to the total, and the combined resistance is less than any single branch. A potential divider shares the supply p.d. in the ratio of its resistances.

8463 past papers

Cambridge 5054 Paper 1Cambridge 5054 Paper 2Cambridge 0625 Papers 2, 4Cambridge 0625 Papers 1, 3Edexcel 4PH1 Paper 1PEdexcel 4PH1 Paper 2P≈ 35 minRevision 11 · updated

Builds on: Resistance

On the AQA 8463 syllabus (First teaching 2016): 2 points this lesson covers
  • 4.2.1.1 Circuit diagram symbols
  • 4.2.2 Series and parallel circuits

Summarised in our own words from the official syllabus. Check the exact wording in the board's specification.

Section 1 of 14

Learning objectives

  • State the current and p.d. rules for series and parallel circuits.
  • Calculate combined resistance in series and for two resistors in parallel.
  • Solve circuits combining series and parallel parts.
  • Use potential dividers, including with thermistors and LDRs.
Pause and think

In an old string of fairy lights, if one bulb failed, they all went out. In your house, if one lamp blows, the others stay on. What's different about the wiring?

Section 2 of 14

Core idea

Start hereOld fairy lights

In old Christmas lights, one dead bulb made the whole string go dark: they were in series. Houses are wired in parallel so one lamp failing leaves the rest on.

The big idea

Series: same current, voltages add, R=R1+R2R=R_1+R_2. Parallel: same voltage, currents add, 1R=1R1+1R2\frac1R=\frac1{R_1}+\frac1{R_2} (less than the smallest).

1. Series and parallel

Series (left) and parallel (right)
4 Ω6 Ω12 V: R = 10 Ω, I = 1.2 A4 Ω6 Ω12 V: 3 A + 2 A = 5 A
Series: 1.2 A through both; the 4 Ω gets 4.8 V and the 6 Ω gets 7.2 V. Parallel: each gets 12 V; currents 3 A and 2 A add to 5 A, so the total resistance is 125=2.4\dfrac{12}{5}=2.4 Ω.
Combining resistors
  1. V=V1+V2=IR1+IR2⇒R=R1+R2V=V_1+V_2=IR_1+IR_2\Rightarrow R=R_1+R_2
    Series: same II, voltages add.
  2. I=I1+I2=VR1+VR2I=I_1+I_2=\frac V{R_1}+\frac V{R_2}
    Parallel: same VV, currents add.
  3. 1R=1R1+1R2\frac1R=\frac1{R_1}+\frac1{R_2}
    Divide by VV.
Worked example4 Ω and 12 Ω on 12 V

In series, then in parallel.

Goal
Currents and voltages.
Strategy
Combine, then V=IRV=IR.
  1. R=16 Ω, I=0.75 AR=16\ \Omega,\ I=0.75\text{ A}
    Series.
  2. V1=3 V, V2=9 VV_1=3\text{ V},\ V_2=9\text{ V}
    0.75×40.75\times4, 0.75×120.75\times12.
  3. 1R=14+112=13⇒R=3 Ω\tfrac1R=\tfrac14+\tfrac1{12}=\tfrac13\Rightarrow R=3\ \Omega
    Parallel.
  4. I1=3 A, I2=1 A, I=4 AI_1=3\text{ A},\ I_2=1\text{ A},\ I=4\text{ A}
    Each gets 12 V.
AnswerSeries: 0.750.75 A, 33 V and 99 V. Parallel: 33 A + 11 A = 44 A.
✓ Check12/3=412/3=4 A ✓; 3+9=123+9=12 V ✓.

2. Potential dividers

Worked example9 V across 2 kΩ and 1 kΩ

Output voltages.

Goal
Two voltages.
Strategy
Voltage shares in the ratio of resistances.
  1. 2:1⇒6 V and 3 V2:1\Rightarrow6\text{ V and }3\text{ V}
    Thirds of 9 V.
  2. LDR in the dark: R↑\text{LDR in the dark: }R\uparrow
    It takes more of the voltage: a light sensor.
Answer66 V and 33 V.
✓ CheckSum 9 V ✓.
Common misconceptionParallel total 1R=13\frac1R=\frac13 means R=3R=3, not 13\frac13.
Pause and think

Why are house lights in parallel?

Series and parallel
RuleSeriesParallel
CurrentSame everywhereSplits; branch currents add to the total
Potential differenceShared; p.d.s add to the supplySame across each branch
Total resistanceR = R₁ + R₂ + …1R=1R1+1R2\frac1R=\frac1{R_1}+\frac1{R_2}; less than the smallest
If one lamp breaksAll go outOthers stay on
Quick check

Why are houses wired in parallel?

Try it: series and parallel circuits
6 VA0.50 AR₁ = 4 ΩR₂ = 8 Ω
CurrentVoltage
R₁0.50 A2.00 V
R₂0.50 A4.00 V
Whole circuit (R = 12.00 Ω)0.50 A6.00 V

Series: the same current flows through both; the voltages add up to the e.m.f.

Compare the two circuits with the same resistors. Adding a resistor in series increases the total resistance; adding one in parallel decreases it.

Summary

  • Series: add.
  • Parallel: reciprocals.
  • Dividers share voltage.
Key words
Potential divider
Resistors splitting a voltage.

Also on your syllabus

  • Circuit diagram symbols to know. Cell, battery, power supply, generator, switch, fixed and variable resistor, potentiometer, heater, thermistor, light-dependent resistor, lamp, motor, ammeter, voltmeter, magnetising coil, transformer, fuse, relay, diode and light-emitting diode (LED).
  • Diodes and LEDs. A diode lets current through in one direction only (the way its triangle points) and has a very high resistance the other way, so it can turn a.c. into d.c. (rectification). An LED is a diode that gives out light when current flows through it the right way.
  • Series p.d. and resistance. With the same current through components in series, the one with the larger resistance has the larger p.d. across it (V=IRV=IR). This is the idea behind a potential divider.
  • Identical sources in parallel give the same e.m.f. as one source on its own (but can supply current for longer).
  • Input sensors. An NTC thermistor's resistance falls as it gets hotter; a light-dependent resistor's (LDR's) resistance falls in brighter light. Placed in a potential divider, either one makes the output voltage change with temperature or light, so it can switch on a fan, an alarm or a street lamp.
  • Junction rule: the current into a junction equals the current out, because charge is conserved. In series the current is the same everywhere and the p.d.s add up to the supply; in parallel the branch currents add up to the total and each branch has the same p.d.
HistoryKirchhoff's rules. In 18451845, as a 2121-year-old student, Gustav Kirchhoff stated two rules: currents into a junction equal currents out, and p.d.s round any loop add up to the e.m.f. These are the series and parallel rules you use today, and they work for any circuit.
Fun factBirds on power lines. A bird sitting on a single high-voltage wire is safe because both its feet are at almost the same potential: there's no p.d. across its body, so no current flows through it. Touching two wires at once would be a different story.
Keep reading for free

Create a free account to read the rest of this lesson: key formulae, worked examples, explore the graph, common mistakes, exam tip, guided practice and more. Your answers are checked and your progress is saved.