Salam Academy
Electricity · Subtopic 2 of 5

Resistance

Resistance tells you how hard it is for current to flow: R=VIR=\dfrac VI, in ohms (Ω). A fixed resistor at constant temperature has a straight-line II–VV graph; a filament lamp curves because its resistance rises as it heats; a diode lets current through in one direction only. Longer, thinner wires have more resistance.

8463 past papers

Cambridge 5054 Paper 1Cambridge 5054 Paper 2Cambridge 0625 Papers 2, 4Cambridge 0625 Papers 1, 3Edexcel 4PH1 Paper 1PEdexcel 4PH1 Paper 2P≈ 30 minRevision 13 · updated

Builds on: Charge, current and potential difference

On the AQA 8463 syllabus (First teaching 2016): 2 points this lesson covers
  • 4.2.1.3 Current, resistance and pd (RP3)
  • 4.2.1.4 Ohmic and non-ohmic components (RP4)

Summarised in our own words from the official syllabus. Check the exact wording in the board's specification.

Section 1 of 14

Learning objectives

  • Use R=VIR=\dfrac VI, rearranged as needed.
  • Describe how to measure resistance with an ammeter and voltmeter.
  • Sketch and explain II–VV graphs for a resistor, filament lamp and diode.
  • Use R∝LR\propto L and R∝1AR\propto\dfrac1A for wires.
Pause and think

The same battery is connected first to a short, thick copper wire, then to a long, thin one. Which carries more current? Why?

Section 2 of 14

Core idea

Start hereWhy a lamp glows but the wires don't

The same current passes through the thin filament and the thick copper leads, yet only the filament glows. The filament resists the current far more, so that's where the energy is transferred.

The big idea

R=VIR=\frac VI (Ω). Ohmic conductor: I∝VI\propto V. R∝R\propto length, R∝1areaR\propto\frac1{\text{area}}.

1. I–V graphs

Circuit for measuring how current varies with voltage
AVVariable resistor changes the currentAmmeter in seriesComponent being testedVoltmeter across it

Tap a label with a dotted underline to find out what it is.

Adjust the variable resistor to get several pairs of readings, then reverse the cell to take negative values. Plot current (y) against voltage (x).
Describe this diagram in words

A circuit loop: a cell, a variable resistor and an ammeter in series with the component being tested. A voltmeter is connected in parallel across the component.

Current–voltage graphs
−6−4−2246−1−0.50.510potential difference (V)current (A)resistor (straight)filament lampdiode
Resistor: straight line through the origin, constant RR. Lamp: curves over, because a hotter filament resists more. Diode: almost no current backwards.
V=IRV=IR
where
RR
resistance (Ω = V/A).
  • Ohmic resistor: straight line through the origin.
  • Filament lamp: curve flattens; resistance rises as it heats.
  • Diode: current one way only.
Worked exampleAn ohmic resistor

6 V gives 0.3 A.

Goal
RR; current at 9 V.
Strategy
R=V/IR=V/I; constant RR.
  1. R=60.3=20 ΩR=\frac6{0.3}=20\ \Omega
    Definition.
  2. I=920=0.45 AI=\frac9{20}=0.45\text{ A}
    Same RR.
Answer20 Ω20\ \Omega; 0.450.45 A.
✓ CheckVV ×1.5, II ×1.5 ✓.

2. Wire dimensions

Resistance of a wire is proportional to its length
204060801001234560length (cm)resistance (Ω)R ∝ L
Measured points scatter slightly about a straight line through the origin.
Worked exampleA 4 Ω wire

Double the length; separately, double the diameter.

Goal
New resistances.
Strategy
R∝LAR\propto\frac LA; area ∝d2\propto d^2.
  1. 2×4=8 Ω2\times4=8\ \Omega
    Longer path.
  2. A×4⇒R=44=1 ΩA\times4\Rightarrow R=\frac44=1\ \Omega
    Double diameter: four times the area.
Answer8 Ω8\ \Omega; 1 Ω1\ \Omega.
✓ CheckThick wires for high currents ✓.
Common misconceptionDiameter vs area Doubling the diameter quarters the resistance, not halves it.
Pause and think

Why does a thermistor's resistance fall when hot?

I–V characteristics
ComponentGraph shapeWhy
Fixed resistor (constant temperature)Straight line through originOhmic: constant resistance
Filament lampCurve flattening at higher VGets hotter, resistance increases
DiodeCurrent only above about 0.6 V forwardConducts in one direction only
Thermistor (NTC)Resistance falls as temperature risesUsed in thermostats
LDRResistance falls as light increasesUsed in light sensors
Quick check

Why does a thicker wire of the same metal and length have less resistance?

Summary

  • V=IRV=IR.
  • R∝LR\propto L, R∝1/AR\propto1/A.
Key words
Ohm
V/A.

Also on your syllabus

  • Ohm's law: the current through a metallic conductor is directly proportional to the p.d. across it, provided the temperature (and other physical conditions) stay constant.
  • Temperature and resistance. As a filament lamp heats up, its metal ions vibrate more and get in the way of the electrons, so its resistance increases. That is why its II–VV graph curves over.
  • Measuring resistance: connect an ammeter in series and a voltmeter in parallel with the component, and use R=VIR=\frac VI.
  • Ohm's law: the current in a metal wire at constant temperature is proportional to the potential difference across it.
HistoryOhm's rejected discovery. Georg Ohm, a schoolteacher, published his law that current is proportional to voltage in 18271827. Critics called it "a web of naked fancies" and he lost his job. Fifteen years later the Royal Society gave him its top medal, and the unit of resistance is named after him.
Fun factSuperconductors: zero resistance. Some materials, cooled to extremely low temperatures, lose all resistance. A current started in a superconducting loop has kept flowing for years with no battery. MRI scanners use superconducting coils to make their strong magnetic fields.
Keep reading for free

Create a free account to read the rest of this lesson: key formulae, worked examples, explore the graph, common mistakes, exam tip, guided practice and more. Your answers are checked and your progress is saved.