Salam Academy
Thermodynamics · Subtopic 1 of 5

Specific Heat Capacity and Latent Heat

Specific heat capacity cc is the energy needed per unit mass per unit temperature rise: Q=mcΔθQ=mc\Delta\theta. Water's cc is about 42004200 J kg⁻¹ K⁻¹. Specific latent heat LL is the energy needed per unit mass to change state at constant temperature: Q=mLQ=mL. Vaporisation needs much more energy than melting because molecules must be completely separated and push back the atmosphere.

9PH0 past papers

Cambridge 9702 Paper 4Edexcel YPH11 WPH15AQA 7408 Paper 2Edexcel 9PH0 Paper 2≈ 35 minRevision 11 · updated

Builds on: Thermal equilibrium and temperature scales

On the Edexcel 9PH0 syllabus (First teaching 2015): 3 points this lesson covers
  • 144 Specific heat and latent heat
  • 145 Thermostat (core practical 12)
  • 146 Measuring latent heat (core practical 13)

Summarised in our own words from the official syllabus. Check the exact wording in the board's specification.

Section 1 of 14

Learning objectives

  • Define specific heat capacity and use Q=mcΔθQ=mc\Delta\theta.
  • Describe an electrical method to measure cc and its errors.
  • Define specific latent heat of fusion and vaporisation; use Q=mLQ=mL.
  • Explain why LvL_v is much greater than LfL_f.
Pause and think

Steam at 100100 °C gives a much worse burn than the same mass of boiling water at 100100 °C. Why?

Section 2 of 14

Core idea

Start hereIce in a drink

An ice cube keeps a drink cold far longer than the same mass of 0 °C water. Melting the ice soaks up a large amount of energy without any temperature change. That's latent heat.

The big idea

E=mcΔθE=mc\Delta\theta (temperature change); E=mLE=mL (state change, constant temperature).

1. The heating curve

Heating curve: steady heater, 0.5 kg ice from −20 °C
2004006008001000120014001600−20204060801001200energy supplied (kJ)temperature (°C)melting: mL_f = 167 kJboiling: mL_v = 1130 kJmcΔθ = 210 kJ
The boiling plateau is much longer than melting: separating particles completely needs far more energy than loosening them.
E=mcΔθE=mLE=mc\Delta\theta\qquad E=mL
where
cc
specific heat capacity (J kg⁻¹ K⁻¹).
LL
specific latent heat (J kg⁻¹).
Worked exampleIce from −20 °C to water at 0 °C

0.5 kg; cice=2100c_{\text{ice}}=2100, Lf=3.34×105L_f=3.34\times10^5.

Goal
Total energy.
Strategy
Warm, then melt.
  1. 0.5×2100×20=21000 J0.5\times2100\times20=21000\text{ J}
    Warm the ice to 0 °C.
  2. 0.5×3.34×105=167000 J0.5\times3.34\times10^5=167000\text{ J}
    Melt at 0 °C.
  3. 188000 J188000\text{ J}
    Add.
Answer1.88×1051.88\times10^5 J.
✓ CheckMelting dominates ✓.

2. Measuring c

Measuring the specific heat capacity of a metal block
AVElectric heaterThermometerMetal blockInsulationPower supply

Tap a label with a dotted underline to find out what it is.

Energy supplied = VIt; c = VIt ÷ (mΔθ). Insulation reduces heat loss, and a drop of oil in the thermometer hole improves thermal contact. Heat lost to the surroundings makes c too large.
Describe this diagram in words

A metal block wrapped in insulation has an electric heater in one hole and a thermometer in another. The heater is connected to a power supply through an ammeter, with a voltmeter across it.

Worked exampleElectrical method

1.0 kg aluminium; heater 12 V, 4.0 A, 300 s; rise 15.6 K.

Goal
cc.
Strategy
VIt=mcΔθVIt=mc\Delta\theta.
  1. E=12×4.0×300=14400 JE=12\times4.0\times300=14400\text{ J}
    Electrical energy.
  2. c=144001.0×15.6=923c=\frac{14400}{1.0\times15.6}=923
    J kg−1^{-1} K−1^{-1}.
Answer923923 J kg−1^{-1} K−1^{-1}.
✓ CheckHeat losses make this an overestimate: insulate ✓.
Key takeawayWhy Lv>LfL_v>L_f Melting loosens bonds; boiling separates molecules completely and pushes back the atmosphere.
Pause and think

Boil off 0.2 kg at 100 °C (Lv=2.26×106L_v=2.26\times10^6)?

Heating equations
ProcessEquationConstant
Temperature changeQ = mcΔθc: specific heat capacity (J kg⁻¹ K⁻¹)
Melting / freezingQ = mL_fL_f: latent heat of fusion (J kg⁻¹)
Boiling / condensingQ = mL_vL_v: latent heat of vaporisation
Worked exampleIce to water

How much energy is needed to turn 0.20 kg of ice at 0 °C into water at 20 °C? (L_f = 3.3 × 10⁵ J kg⁻¹, c = 4200 J kg⁻¹ K⁻¹)

Goal
Total energy.
Strategy
Melt first, then warm the water.
  1. Melt: 0.20 × 3.3 × 10⁵ = 66 000 J.

    Temperature constant.
  2. Warm: 0.20 × 4200 × 20 = 16 800 J.

    Q = mcΔθ.
  3. Total = 82 800 J.

    Add.
Answer8.3 × 10⁴ J
✓ CheckMelting takes about four times more energy than warming by 20 K ✓.
Quick check

Why is the latent heat of vaporisation much larger than the latent heat of fusion?

Summary

  • mcΔθmc\Delta\theta on slopes; mLmL on plateaus.
Key words
Specific latent heat
Energy per kg to change state.

Also on your syllabus

  • Specific latent heat: energy to change the state of 1 kg without a change in temperature, Q=mLQ=mL; latent heat of fusion for melting, of vaporisation for boiling.
HistoryBlack's hidden heat. In the 17601760s Joseph Black noticed that melting ice absorbs heat without getting warmer, calling it "latent" (hidden) heat. His student James Watt used the idea to make steam engines far more efficient by condensing steam in a separate chamber.
Fun factWhy coastal cities are mild. Water's specific heat capacity is about five times that of rock and sand. Oceans warm and cool slowly, so seaside cities like Karachi have much smaller temperature swings between summer and winter than inland cities like Jacobabad.
Keep reading for free

Create a free account to read the rest of this lesson: key formulae, worked examples, explore the graph, common mistakes, exam tip, guided practice and more. Your answers are checked and your progress is saved.