Salam Academy
Materials · Subtopic 3 of 4

Stress, Strain and the Young Modulus

A spring or wire obeys Hooke's law, F=kxF=kx, up to its limit of proportionality. To compare materials rather than particular objects, use stress (σ=FA\sigma=\tfrac FA) and strain (ε=xL\varepsilon=\tfrac xL). Their ratio in the linear region is the Young modulus, E=σεE=\dfrac\sigma\varepsilon, a property of the material alone.

9PH0 past papers

Cambridge 9702 Paper 1Cambridge 9702 Paper 2Edexcel YPH11 WPH11AQA 7408 Paper 1Edexcel 9PH0 Paper 2≈ 35 minRevision 12 · updated

Builds on: Moments, couples and equilibrium

On the Edexcel 9PH0 syllabus (First teaching 2015): 3 points this lesson covers
  • 53 Hooke's law
  • 54 Stress, strain and Young modulus
  • 57 Measuring the Young modulus (core practical 5)

Summarised in our own words from the official syllabus. Check the exact wording in the board's specification.

Section 1 of 14

Learning objectives

  • Use Hooke's law and the spring constant.
  • Define and calculate stress and strain.
  • Calculate the Young modulus, including from a graph.
  • Describe an experiment to measure the Young modulus of a wire.
Pause and think

A thick steel cable and a thin steel wire are stretched by the same force. The thin wire stretches far more. Is the thin wire made of "stretchier" steel?

Section 2 of 14

Core idea

Start hereThick and thin wires

Hang the same load on a thick and a thin steel wire: the thin one stretches more. So stiffness depends on the sample. But divide force by area and extension by length, and every steel wire gives the same ratio: the Young modulus, a property of steel itself.

The big idea

σ=FA\sigma=\frac FA, ε=ΔLL\varepsilon=\frac{\Delta L}L, E=σε=FLAΔLE=\frac\sigma\varepsilon=\frac{FL}{A\Delta L} in the elastic region.

1. Definitions

Measuring the Young modulus of a metal wire
original length L (about 2 m)Wire clamped at one endMarkerFixed rulerMasses add load F

Tap a label with a dotted underline to find out what it is.

Measure the diameter with a micrometer in several places to find A. Add masses, record the extension of the marker each time, and plot stress against strain: the gradient of the straight part is the Young modulus.
Describe this diagram in words

A long thin wire is clamped at one end of a bench and runs over a pulley at the other end, where a hanger of masses pulls on it. A small marker on the wire sits over a fixed ruler, and the original length L from the clamp to the marker is shown.

σ=FAε=ΔLLE=FLA ΔL\sigma=\frac FA\qquad\varepsilon=\frac{\Delta L}L\qquad E=\frac{FL}{A\,\Delta L}
where
σ\sigma
stress (Pa).
ε\varepsilon
strain (no units).
EE
Young modulus (Pa).
Stress–strain graph for a metal wire
0.0020.0040.0060.0080.010.0121002003004005000strainstress (MPa)limit of proportionalitybreaksgradient = EUTS (max stress)
Gradient of the straight part =400×1060.002=2×1011=\dfrac{400\times10^6}{0.002}=2\times10^{11} Pa: the Young modulus of steel.
Worked exampleSteel wire

L=2.0L=2.0 m, diameter 0.500.50 mm, load 50 N, E=2.0×1011E=2.0\times10^{11} Pa.

Goal
Extension.
Strategy
Area → stress → strain → extension.
  1. A=π(0.25×10−3)2=1.96×10−7 m2A=\pi(0.25\times10^{-3})^2=1.96\times10^{-7}\text{ m}^2
    Radius, not diameter.
  2. σ=501.96×10−7=2.55×108 Pa\sigma=\frac{50}{1.96\times10^{-7}}=2.55\times10^8\text{ Pa}
    Stress.
  3. ε=2.55×1082.0×1011=1.27×10−3\varepsilon=\frac{2.55\times10^8}{2.0\times10^{11}}=1.27\times10^{-3}
    Strain.
  4. ΔL=2.0×1.27×10−3=2.5 mm\Delta L=2.0\times1.27\times10^{-3}=2.5\text{ mm}
    Extension.
Answer2.52.5 mm.
✓ CheckFLAE=10039200=2.55×10−3\frac{FL}{AE}=\frac{100}{39200}=2.55\times10^{-3} m ✓.
  • Limit of proportionality: end of the straight part.
  • Elastic limit: beyond it, permanent deformation.
  • Ultimate tensile stress: maximum stress.
Exam tipMeasuring E Long thin wire; micrometer for diameter in several places; marker for extension; plot stress vs strain.
Common misconceptionDiameter as radius Halve the diameter before πr2\pi r^2.
Pause and think

Double the diameter, same load and length. Extension ratio?

Stress, strain and Young modulus
QuantityEquationUnit
Stressσ=FA\sigma=\frac FAPa (N m⁻²)
Strainε=ΔLL\varepsilon=\frac{\Delta L}{L}none
Young modulusE=σε=FLAΔLE=\frac{\sigma}{\varepsilon}=\frac{FL}{A\Delta L}Pa
Elastic strain energy12FΔL\frac12F\Delta L = area under F–x graphJ
Quick check

Why is the wire in a Young modulus experiment long and thin?

Summary

  • σ=F/A\sigma=F/A, ε=ΔL/L\varepsilon=\Delta L/L.
  • EE = gradient of linear region.
Key words
Young modulus
Stress ÷ strain in the elastic region.

Also on your syllabus

  • Tensile and compressive forces. A pair of forces pulling outwards on an object (tension) stretches it: a tensile deformation, measured by its extension. A pair pushing inwards squashes it: a compressive deformation, measured by its compression. Hooke's law, stress, strain and the Young modulus apply to both, as long as the limit of proportionality is not passed.
  • Spring constant: k=Fxk=\frac Fx, force per unit extension, in N m⁻¹; a stiffer spring has a larger kk.
HistoryThomas Young, polymath. Thomas Young described the modulus that bears his name in 18071807. He also showed light is a wave (the double-slit experiment), studied how the eye focuses, and helped decipher the Rosetta Stone. He was called "the last man who knew everything".
Fun factSpider silk beats steel. Weight for weight, spider dragline silk is stronger than steel and far tougher, stretching about 30%30\% before breaking. Scientists are engineering bacteria and goats to produce it for bulletproof vests and surgical threads.
Keep reading for free

Create a free account to read the rest of this lesson: key formulae, worked examples, explore the graph, common mistakes, exam tip, guided practice and more. Your answers are checked and your progress is saved.